Truss bar forces by the method of sections
The same truss as in the method of joints example, but now we only look for the forces in three bars: we cut the truss through these bars and write equilibrium equations for one of the parts.
The problem
Determine the forces in the three cut bars by the method of sections (Ritter method).
The truss and the loads
Step 1: the support reactions
Treating the truss as a single rigid body, we write the three equilibrium equations.
Support reactions
Assumed positive directions: forces ↑ and →, moments ↺.
ΣFx = 0:
Ax + F3 = 0
Ax + 5 = 0
⇒ Ax = −F3 = −5
⇒ Ax = −5 kN (←)
ΣMA = 0:
Dy·9 − F1·3 − F2·6 − F3·3 = 0
Dy·9 − 20·3 − 10·6 − 5·3 = 0
⇒ Dy = F1·3 + F2·6 + F3·39 = 20·3 + 10·6 + 5·39
⇒ Dy = 15 kN (↑)
ΣFy = 0:
Ay + Dy − F1 − F2 = 0
Ay + 15 − 20 − 10 = 0
⇒ Ay = −Dy + F1 + F2 = −15 + 20 + 10
⇒ Ay = 15 kN (↑)
Check
ΣMD = 0:
−Ay·9 + F1·6 + F2·3 − F3·3 = 0
−15·9 + 20·6 + 10·3 − 5·3 = 0
⇒ 0 = 0 ✓
Step 2: the section
The section divides the truss into two parts; we examine the part with fewer external forces acting on it. For each bar force we are looking for, we write a moment equation about the intersection point of the lines of action of the other two cut bars, the Ritter point, so it has only one unknown. If two bars are parallel, we use the force equation perpendicular to them.
We cut the truss through the three chosen bars and write equilibrium equations for one part. The forces of the cut bars are assumed to be tensile (pointing from the examined part towards the cut). For each bar force we write a moment equation that contains only that one unknown: about the intersection of the lines of the other two bars (Ritter point). If the other two bars are parallel, we write the projection equation perpendicular to them.
Assumed positive directions: forces ↑ and →, moments ↺.
1. section: SBC, SCE, SEF
The section splits the truss into two parts. We examine the right part (nodes C, D, F), because fewer external forces act on it.
With the components instead of the inclined bar forces:
Angles of the inclined cut bars (from the horizontal and vertical projections of the bar):
tg αCE = 33 ⇒ αCE = 45° ⇒ SCEx = SCEy
SBC: the lines of action of bars SCE and SEF intersect at point E (3; 3); we write a moment equation about this point. Bar SBC is horizontal; its lever arm is the vertical distance between point E and the bar: k = 3 m.
ΣME = 0:
−SBC·3 − F2·3 + Dy·6 = 0
−SBC·3 − 10·3 + 15·6 = 0
⇒ SBC = −F2·3 + Dy·63 = −10·3 + 15·63
⇒ SBC = 20 kN (tension)
SEF: the lines of action of bars SBC and SCE intersect at point C (6; 0); we write a moment equation about this point. Bar SEF is horizontal; its lever arm is the vertical distance between point C and the bar: k = 3 m.
ΣMC = 0:
SEF·3 + Dy·3 = 0
SEF·3 + 15·3 = 0
⇒ SEF = −Dy·33 = −15·33
⇒ SEF = −15 kN (compression)
SCE: the other two bars (SBC, SEF) are parallel, so we write the projection equation perpendicular to them (ΣFy = 0).
ΣFy = 0:
SCEy − F2 + Dy = 0
SCEy − 10 + 15 = 0
⇒ SCEy = F2 − Dy = 10 − 15
⇒ SCEy = −5 kN
From the angle the other component, then from the two components the bar force SCE:
⇒ SCEx = SCEy = −5 kN
⇒ SCE = −SCEx2 + SCEy2 = −(−5)2 + (−5)2
⇒ SCE = −7.071 kN (compression)
Compared with the result of the method of joints:
SBC = 20 kN, SCE = −7.071 kN, SEF = −15 kN ✓